Wasp W-300 Podręcznik Użytkownika

W-300 Thermal Label PrinterUser’s Guidefor Wasp Bar Code Technologies®DT/TT Printer

6Quick Setup GuideLoading the Ribbon4. Unwrap the ribbon package and separate the ribbon roll and the empty core.Ribbon Supply HolderRibbon RollNotchR

7Quick Setup GuideLoading the RIbbon6. Insert empty core into the outer ribbon supply take-up holder. (First snap in left side by aligning notches in

8Quick Setup GuideLoading the Ribbon7. Turn the take-up wheel forward and rewind the excess ribbon.Wheel

9Quick Setup GuideLoading the MediaStandard Mode - (Direct Thermal and Thermal Transfer)1. Lift the top cover to expose the media compartment.

10Quick Setup GuideLoading the Media3. Load the media roll onto the holder from the left.Media CompartmentMedia HolderMedia HolderMedia Roll2. Remove

11Quick Setup GuideLoading the Media4. Place the media holder back to the media compartment.5. Move the media roll to the left end of the holder.6. Sl

12Quick Setup GuideLoading the Media7. Hold the print head module upright with one hand to allow the media to pass under it.Lead the media through the

13Quick Setup GuideLoading the Media10. Close the top cover and turn on the printer or press the feed button if the printer is already on.Print Head M

14Performing CalibrationNote: This step is very important and must always be carried out whenever media is being changed. Failure to do so will result

15Chapter 1Operator ControlsOperator ControlsPower Switch - Controls printer powerOn - normal operationOff - the power should be turned off before con

© Copyright Wasp Bar Code Technologies 2001.All rights reserved.No part of this publication may be reproduced or transmitted in any formor by any mean

16Chapter 2Resetting the PrinterResetting the Printer to FactoryDefault Settings1. Turn on the printer and wait for approximately 5 seconds.2. Press t

17Chapter 3Printer DriverPrinter DriverThe bundled printer driver is compatible with Windows 2000/ME/9x, and WindowsNT.Through this driver you may pri

18Chapter 4Setting Printer PropertiesSetting Printer PropertiesAfter installing the driver, follow the steps below to modify the printer properties:1.

19Chapter 4Setting Printer Properties (cont.)Media choice (Darkness)Some printing applications require changes to the darkness setting.This settingact

TroubleshootingNormally, when the printer has an error, the “Power” or the “Ready” LED will blink.To understand the problem, please check both LEDs fi

21Chapter 5TroubleshootingB. Power and Ready LEDs blink alternatelyPossible Solutions Refer to PagesProblemsRibbon empty • Reload ribbon 5-9Ribbon jam

22Chapter 5TroubleshootingD. MiscellaneousThe PC says “Printer Time Out”1. Make sure the communications cable (parallel or serial) is connectedsecurel

23Chapter 6Printer MaintenanceClean the following areas of the printer after 8 rolls of labels have been used. Ineach case, use a cotton swab dampened

24Chapter 7Technical SpecificationsModel W-300 Thermal Transfer PrinterPrint Method Direct Thermal or Thermal TransferResolution 203 DPIPrint Width Up

25Chapter 8Product Support & Warranty InformationWasp W-300 Printer is wa r r anted against defects in wo rkmanship and materi a l sfor a period o

Table of ContentsQuick Setup GuideInspecting the Printer ...1Connection Diagram...

1Quick Setup GuideInspecting the PrinterAfter removing the printer from the packaging material, check the contents ofthe package.The following items s

2Quick Setup GuideConnection DiagramAC Electrical OutletPower AdapterTo PCBarrel ConnectorPower JackPower SwitchParallel Port

3Power SupplyQuick Setup GuideConnecting the PrinterNote: The power supply must be connected into the back of the printer beforeconnecting the communi

4Note:This section is not applicable to Direct Thermal (DT) printing.Quick Setup GuideLoading the RibbonLoading the Ribbon1. Lift the top cover to exp

5Loading the RibbonQuick Setup GuideLoading the RibbonMedia CompartmentPrint Head ModuleRelease LeverRelease LeverRibbon Supply Holder2. Unlatch the p